In the early stages of designing and developing a pelletizing plant, many questions often arise: what equipment will best suit my process; do I need a binder; how tall will my building have to be, and more. While this process prompts a host of questions, these questions are easily answered by working with a pelletizing expert.
As the leader in pelletizing equipment and process systems, we have collected and answered the most frequently asked questions we receive throughout our work in pelletizing plant design below.
Note: This article refers exclusively to the tumble-growth/non-pressure form of pelletizing, also known as agitation agglomeration or wet granulation.
What pelletizing equipment will be best for my material and process goals?
Within the category of pelletizing, a few different types of equipment exist. This equipment may be employed on a stand-alone basis, or combined to reach the desired end product characteristics. Equipment most commonly used for pelletizing includes:
- Rotary Drum Agglomerators (aka granulation drums)
- Disc Pelletizers (aka pan granulators)
- Pugmill Mixers (aka pug mills or paddle mixers)
- Pin mixers
- Coating Drums (for post-agglomeration treatment)
Many factors influence the equipment decision, with cost, processing environment, capacity, and other variables coming into play. In the case of many pelletizing plants, the intended process is best evaluated through feasibility testing, followed by continuous pilot-scale trials to assess how the material will respond to pelletizing, as well as what equipment will be most suitable for the specific process objectives.
Testing in a facility like the FEECO Innovation Center yields a range of information that helps to guide the equipment configuration and process parameters.
Do I need a binder?
All pelletizing operations require some form of binding agent to cause particles to gather and adhere together. This is often supplied in the form of a liquid binder, or if agreeable to the material, water.
In some less common cases, the chemical composition of the material may be such that a constituent can serve as the binding agent, negating the need for an additional binder.
As well as facilitating pellet formation, the liquid binder ensures adequate green strength (so pellets don’t break apart during subsequent processing) and helps to reach the desired end product crush strength. As such, binder selection is an important aspect of pelletizing process development.
Do I need to dry the pellets?
In almost all cases, the pellets will require drying. This is typically carried out in a rotary dryer, which offers the added benefit of further rounding and polishing pellets as a result of the tumbling action that occurs in the dryer.
Drying serves several objectives, essentially curing the pellet into its final hardened form. Without drying, pellets would be malleable and unable to hold up to storage and transportation. They would also be much more susceptible to caking.
Drying also helps to prevent mold and bacterial growth in pellets after processing. Further, it reduces the cost of transportation, by reducing the amount of water being carried.
Pellets that will be immediately fed to a rotary kiln also still typically require a drying step.
Will there be any recycle?
Yes. All pelletizing/wet granulation processes yield some level of recycle. The amount of recycle produced depends on the chosen equipment configuration, with disc pelletizers producing less recycle than rotary drum agglomerators.
A common misconception when it comes to pelletizing plant configuration is that any amount of recycle is bad. While recycle does reduce process efficiency, it is also an important part of the production process; recycle can serve as a back-mixing feed to reduce the moisture content of the feedstock. Further, it provides a buffer to the process, so that if an upset were to occur, the recycle on-hand could be used to even things out and prevent the product from being immediately affected.
How many workers do I need to operate the pelletizing plant?
As a general rule, a pelletizing plant requires one operator and one supervisor. This may differ depending on the equipment setup; while one operator can supervise several drum agglomerators, a single operator should only supervise a few disc pelletizers. Operations utilizing several pelletizers typically benefit from more than one operator. Further, depending on how much time the operator must dedicate to watching the disc(s), or if the raw material feed and product offtake are transferred with a front-end loader, additional labor may be helpful.
Does the equipment need to be placed indoors?
Many types of equipment can operate reliably in the long-term in an outdoor setting if properly protected and maintained. Rotary dryers, for example, are designed to operate in both indoor and outdoor settings.
Disc pelletizers, however, are generally best kept indoors, because the disc pelletizer is considered an “open system,” meaning the processing occurs in an open-air environment. While this allows operators the ability to monitor and make adjustments during processing (a key advantage of the disc pelletizer), it also leaves the material exposed to the external environment. Were a disc pelletizer installed outside, wind, rain, and other factors could cause problems.
How tall does my building need to be?
Building height requirements vary significantly and depend on the plant’s capacity, as well as whether the production line will be laid out vertically or horizontally.
How finely do my materials need to be ground?
A good starting point for feedstock particle size distribution is to have all material at minus 250 micron, though this can vary based on the material’s unique characteristics and response to agglomeration. It is also desirable to have a good cross section of particle sizes so that when joined together, smaller particles fill in the spaces between larger particles, creating a stronger agglomerate with fewer void spaces.
The uniformity of feedstock is also an important consideration; the presence of large lumps or a general lack of uniformity in the feedstock often will not produce the desired results and could even cause process upsets.
How can I de-risk the scale-up process?
The process development journey can be de-risked by utilizing testing services such as those offered by the FEECO Innovation Center. Testing the material first at batch scale, and then at pilot scale, is incredibly valuable in preventing surprises on scale-up, evaluating the process economics, identifying potential issues early, and allowing those issues to be addressed during the design stages.
Conclusion
FEECO has been the leader in pelletizing (tumble-growth agglomeration) technology since 1951. Our extensive experience around hundreds of materials provides unmatched expertise.
While the process of building a pelletizing plant is often surrounded by a host of questions, we are ready to guide you through the process of building a plant that suits your specific process and material goals. For more information on our pelletizing plants and services, contact us today!